Home  /   ASTM B166 PDF

Metal Type. UNS N Bar. ASTM B AMS Din Wire. Sheet. ASTM B AMS Din Plate. ASTM B AMS Din VAT (Alloy / ASTM B / UNS N) Nickel Alloy As it is corrosion resistant in oxidizing and reducing conditions, this alloy is virtually free of. ASTM Standards: 3. B Specification for Nickel-Chromium-Iron Alloys 1 This specification is under the jurisdiction of ASTM Committee B02 on.

Author: Shataxe Taurisar
Country: Netherlands
Language: English (Spanish)
Genre: Medical
Published (Last): 19 July 2006
Pages: 83
PDF File Size: 14.50 Mb
ePub File Size: 7.5 Mb
ISBN: 396-7-87919-273-6
Downloads: 96839
Price: Free* [*Free Regsitration Required]
Uploader: Kagarr

Rejection and Rehearing Examples of such requirements include, but are not limited to, the following: Hot-worked zstm to be machined in longer lengths should be speci?

Villares Metals International

For cold-worked rods and bars under 1? D Forging quality is atm to chemical requirements and surface inspection only. Test Chemical composition, hardness, and tolerances when expressed in decimals Rounded Unit for Observed Or Calculated Value Nearest unit in the last righthand place of?

If two choices are possible, as when the digits dropped are exactly a 5, or a 5 followed only by zeros, choose the one ending in an even digit, with zero de? Cold-worked wire shall not be out-of-round by more than one-half the total permissible variations in diameter shown in Table 6.


When a full cross-section size test cannot be performed, the largest possible round specimen shown in Test Methods E 8 shall be used. For each multiple, an allowance of 1?


Type C-3 for finishing. All sizes UNS N The purchaser shall have the right to perform any of the inspections or tests set forth when such inspections and tests are deemed necessary to ensure that the material astmm to prescribed requirements. Furnished in multiples of a speci? The chromium content of the alloy makes it superior to commercially pure nickel under oxidizing conditions.

C Hardness B75 to B95, or equivalent. E High-temperature annealed condition.

Inconel 600 (UNS N06600) Ni 76.0, Cr 15.5, Fe 8.0 Description

In the event that more critical quality or more rigid inspection standards than those called out in this speci? Hardness B75 to B, or equivalent.

Bar stock may need to be stress relieved, or annealed before performing any heading operations. Machining Type Suggested starting rates are: Request quote on this grade. B b1166 08 3 Not for Resale Element shall be determined arithmetically by difference. This standard has been approved for use by agencies of the Department of Defense.

This abstract is a brief summary of the referenced standard. C Applicable to 3 ft 0. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Special End Uses S1. Alloy is used in chemical and food processing, heat treating, phenol condensers, soap manufacture, vegetable and fatty acid vessels and many more.


Intended generally for machining where an overhauled surface is desired, essentially for machined step down shafts or parts machined in short lengths of 3 ft 0.

Your comments will receive careful consideration at a zstm of the responsible technical committee, which you may attend. In case of dissatisfaction with the xstm of the test, the producer or supplier may make claim for a rehearing. The nickel content gives it excellent resistance to chloride-ion stress-corrosion cracking and also provides excellent resistance to alkaline solutions.

Work Item s – proposed revisions of this standard.

Same as diameter of wire. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

This standard does not purport to address all of the safety concerns, if any, associated with its use. High Performance Alloys stocks and produces Inconel in this grade in the following forms: