Designation: F /F M â 07 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This. ASTM F/FM: Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series. Designation: F /F M – 05 Standard Speci?cation for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This.
|Published (Last):||22 March 2014|
|PDF File Size:||18.56 Mb|
|ePub File Size:||15.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM B – The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. There were no books found for the applied search filters.
The section shall be etched for microscopic examination in accordance with Test Method E Users aztm this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.
No items in cart. Published on Nov View Download They arenot planished during forging. Limits are specified in5. This standard has been approved for use by agencies of the Department of Defense. Typical voids are aztm in Fig.
Print 1 2 3 4 5 page sstarting from page current page. Typical tool marks are shown in Fig. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.
A number in parentheses indicates the year of last reapproval. FORMAT Single User Subscription Site License Subscription BOOKS All Books PACKAGES All Packages EDITION to PUBLISHER. This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of MPa and higher; and inch series products with nominal diameters of No. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the aboveaddress or at phonefaxor service astm. Combining values from the two systems may result in nonconformance with the specification.
Types of surface discontinuities are: There are no ISO standards for surface discontinuities on any inch-series products. This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of MPa and higher; and inch series products with awtm diameters of No. Voids are produced by marks or impressions of chips shear burrs or by rust formation on the raw material.
Acceptance shallbe based on the requirements of S1. Land Use and Development. Typical shear bursts are shown in Fig.
If ast feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.
Supplementary Requirements shall in no way negate any requirement of the speci? The section shall be etched for microscopic examina-tion in accordance with Test Method E ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.
A superscript epsilon e indicates an editorial change since the last revision or reapproval. There are no ISO standards for surfacediscontinuities on any inch-series products. Referenced Documents purchase separately The documents listed below astk referenced within the subject f78 but are not provided as part of the standard. After etch, the samples shall be examined under a 10 3 magni? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Shear bursts may also occur on the sides of hex-head products. Enter your account email address to request a password reset: The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. NOTE 2Bursts and shear bursts within the limits of this specificationmay be unsightly, but do not affect the mechanical properties or functionalrequirements of the bolt.
These surface discontinuities shall be inspected in accordance with the specified requirements.
Search book title Enter keywords for book title search. Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence.
Combining values asttm the two systems may result in non-conformance with the standard. Enter your personal account email address to request a password reset: They are not planished during forging. Register for a trial account. There are no ISO standards for surface discontinuities axtm any inch-series products.