DIN 43673 PDF

Home  /   DIN 43673 PDF

Draft standard [WITHDRAWN] DIN VDE – Draft. Erection of power installations with rated voltages exceeding 1 kV. from EUR VAT. Find the most up-to-date version of DIN at Engineering and protect it from deterioration. Bolting arrangements (DIN 43 ). Bar Torque Nm to DIN Plain washer to DIN Spring disc washer to DIN

Author: Goshura Tataxe
Country: Peru
Language: English (Spanish)
Genre: Life
Published (Last): 24 April 2012
Pages: 494
PDF File Size: 14.92 Mb
ePub File Size: 9.67 Mb
ISBN: 863-1-75708-766-5
Downloads: 54928
Price: Free* [*Free Regsitration Required]
Uploader: Malamuro

CUAL bars may be slightly bent.

DIN 43673-2:1982-02

Do not bend over sharp edges; only perform drilling and punching after bending; avoid sudden deformation pressure. In order to ensure good electrical contact between the busbars, it is necessary to penetrate 4373 surface film of oxides, sulphides, and other contaminants.

The contact will therefore be better if the 436773 is rough, has pressing lines, or has been knurled. Copper oxide has a considerably lower electrical resistance than aluminium oxide and a negative temperature resistance coefficient. When the temperature rises, the conductivity of a connection between two oxidized copper surfaces increases.

Since CUAL has a copper plating, it has the same outstanding contact properties as copper, and so CUAL bars can be used in the 43637 way as copper bars. The contact between the surfaces is initially limited to the tip of each surface, which are therefore subjected to a significantly higher pressure than the average pressure of the connection.

  HEIDENHAIN DA300 PDF

Deformations therefore occur during the binding process. In a completed connection, the actual contact area is significantly smaller than vin of the total surface area of the connection.

Copper-Aluminium Bars (CUAL)

The effective contact area is normally limited to the surface near the bolts. The contact area should be flat, clean, and uniformly roughened. Exaggeratedly flat surfaces are not necessary for the connection, since diin connection is clean and fixed.

A slight improvement can be achieved here: If the surfaces are pressed together to be connected without the Vaseline being removed, the excess Vaseline is pressed out and contributes to the sealing of dun connection and to the protection against harmful effects. Dn a given contact pressure, a copper surface has a contact resistance that is times lower than that of aluminium. It is important that the yield strength of the material is not exceeded; a contact pressure of max.

The creep behaviour of CUAL lies between that of copper and aluminium. The screws can be made of a wide variety of steel grades, brass, or bronze. Due to their higher availability, steel screws are recommended. These should be higher strength 8.

The contact pressure should be spread out across oversized washers. Spring washers are preferable for obtaining a constant pressing force during the various thermal stresses. They ensure the different expansions between the screws and the bar and compensate for any potential relaxations of the metal. CUAL can be tin- and silver-plated. CUAL can be cut using the same method as aluminium. Therefore, cutting with every second saw tooth produces good results.

  6ED1 052-1MD00-0BA7 PDF

Deburring is not necessary.

DIN – European Standards

The data in this technical product information is based on our current xin and experience. Due to the abundance of possible influences during its application, it does not release the processor nor the user from performing their own tests and trials.

A legally binding guarantee of certain properties or of suitability for a specific purpose cannot be derived from our information. Depending on the individual case, we recommend consulting with us. Any property rights and existing laws must be observed by the recipient of our products under their fin responsibility.

CUAL bars – EN | anoxal

We only use cookies when they are necessary. With the further use of our website you accept the usage of cookies. Recommendation for drilling Cutting speed: The punching tool is constructed just like for flat copper bars. The template 4673 be as close as possible to the shearing edge so that the material is adequately supported.

Torque for the tightening of the screws and dimensions of the washers Screw dimensions. Recommendations for cutting Cutting speed: